a list of all the bushing I would need to replace all the bushings on my celi. It had all the part numbers and everything. Tax returns are coming and I have to replace alot of stuff here is a little list. PS Pump PS High Pressure Hose PS Rack Polyurethane Bushing Polyurethane Motor Mounts Eibach Springs Short Ram intake New Exhaust
get an aftermarket exhaust, bosal is a stock sound upgrade good luck finding an intake, i'd jsut make one eibach's are nice so are intrax poly bushings are hard to find but doable...i don't remember where to get them, while you are at it upgrade the swaybar bushings there are no poly motor mounts but i do have a friend that can make them pump, i'd get a yoda one, line and rack carquest has very nice ones.
Damn I know I seen it somewere in here or on another celica forum. About the list of parts that was some wishful thinking its going to go like this in order. Poly Motor Mounts (They do make them I found them somewere too) Poly bushings (I know I seen them somewere) Power Steering(Will Purchase Genuine Toyota) Rack and line (Will check out carquest) Brake Lights (Put it into dealership for diagnosis) Intake( I will make my own SRI) Exhaust( Just fix exhaust leaks and a new muffler) I have a friend in the body shop that I work at that said on a weekend I could come in and sand my car down, and he would primer and paint it for me for like $300.
Do the speed source motor mounts work for the regular 4th gens? I know they work for my 165. You might try those. They are amazing.
Sure, Superpro polyurethene bushings have a full line for our cars. I have their catalog at home, so I can get you the specific part#s. But that won't be until after the holidays.
They should work but the tranny and rear mount are different. Because the crossmember on the 165 and 162 are different..I thought I heard that somewere
the crossmember is shaped different but I don't think the actual mount design is any different. Which would allow the speed source's mounts to work.
the mounts should all be the same, though i'm not sure about the tranny one. but as far as poly mounts go the only ones you'll need to change are the ones on the crossmember.
the speedsource front and rear poly mounts for the All-Trac work just fine in the regular celi's, definite improvement, just be prepared to "feel" your motor.
Another option, and I don't remember the specific part numbers, is Chevy transmission polyurethene bushings.
bushings !~!! woot AHHH iVE FOUND IT ONLY TOOK 2 HOURS OF SURFING!!! www.toyheadauto.com Celica 86 to 89 ST162, SX162 & ST165 GT4 Front Lower Control Arm Front Bushing -1044K- (2 bushings with collar tubes), Standard alignment settings. $29.71 Front Lower Control Arm Rear Bushing -1363K- (2 bushings with 2 collar tubes and 2 washers) PS & DS standard caster setting. $38.35 Front Lower Control Arm Rear Bushing -1364K- (2 bushings with 2 collar tubes and 2 washers) PS increased DS standard caster setting. $38.35 Front Lower Control Arm Rear Bushing -1365K- (2 bushings with 2 collar tubes and 2 washers) PS increase & DS decrease caster. $38.35 Front Lower Control Arm Rear Bushing -1365AK- (2 bushings with 2 collar tubes and 2 washers) PS & DS increase caster . $38.35 Front Sway Bar Mount to Chassis bushing kit -1335-__ K - (2 bushings) $15.24 GT4, ST165 Measure bar diameter 16, 25, 26 & 27 mm available. $15.24 Rear Control Arm Outer Bushing -2372K- (4 bushings with collar tubes) front arm only. $28.51 Rear Control Arm Outer Bushing -1220K- (2 bushings with collar tubes) Does not fit GT4, rear arms only, 35mm out side diameter, 14mm bolt. $23.11 Rear Control Arm Outer Bushing -2263K- (8 bushings with collar tubes) GT4, ST165. $65.18 Rear Control Arm Inner Front Bushing-2264K- (4 with collar tubes) GT4, ST165. $47.31 Rear Control Arm Inner Rear Bushing -2265K- (4 bushings with collar tubes) GT4, ST165. $45.62 Rear Sway Bar to Chassis Mount bushing kit -0331-__K- (2 bushings) Measure bar diameter 13, 19 mm available. $19.18 Rear Trailing Arms bushing kit, -0823K- (8 bushings, 4 tubes) $46.31
These are all I need out of that list right. Front Lower Control Arm Front Bushing -1044K- (2 bushings with collar tubes), Standard alignment settings. $29.71 Front Lower Control Arm Rear Bushing -1363K- (2 bushings with 2 collar tubes and 2 washers) PS & DS standard caster setting. $38.35 Front Sway Bar Mount to Chassis bushing kit -1335-__ K - (2 bushings) $15.24 GT4, ST165 Measure bar diameter 16, 25, 26 & 27 mm available. $15.24 Rear Control Arm Outer Bushing -2372K- (4 bushings with collar tubes) front arm only. $28.51 Rear Control Arm Outer Bushing -1220K- (2 bushings with collar tubes) Does not fit GT4, rear arms only, 35mm out side diameter, 14mm bolt. $23.11 Rear Sway Bar to Chassis Mount bushing kit -0331-__K- (2 bushings) Measure bar diameter 13, 19 mm available. $19.18 Rear Trailing Arms bushing kit, -0823K- (8 bushings, 4 tubes) $46.31
Yeah..youll definitely feel your motor. I used speed sources. Took about an hour to swap them. Definite improvement.