1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Jdm ecu

Discussion in 'Diagnosis/Help' started by Nando512, Feb 6, 2013.

  1. Nando512

    Nando512 Member

    Does any one know what a jdm ecu looks like or the numbers for one I found some on eBay but I'm sure if there jdm or usdm I found one that says


    Toyota
    89661-20280

    176000-0641​

    So my question is does any one know the number sequence for the jdm ecu for the 3sge​
     
  2. Stig

    Stig ST162 Guru Donated!

    That is not JDM

    mine:

    [​IMG]

    I seriously doubt you'll find them on ebay, even here they are scarce and expensive
    There is no 20280 - only 28280, which is the GTE ecu fitted to all ST165's

    We had a thread covering all this but it was damaged in the crash of 2009, all that is left is the last page http://www.st162.net/forum/showthread.php?3166-please-post-your-ecu-s
     
    Last edited: Feb 6, 2013
  3. eNtraxGT88

    eNtraxGT88 Well-Known Member Donated!

    http://www.st162.net/forum/showthread.php?5438-1st-gen-3sge-jdm-ecu&p=69628&viewfull=1#post69628

    actually the 20280 is the pre-facelift USDM 3S-FE ecu. and actually, the GTE for usdm runs on 20360 ecu.
     
    Last edited: Feb 7, 2013
  4. Stig

    Stig ST162 Guru Donated!

    Actually 28280 is all JDM ST165's, I note there is a 20370 fitted to a car in Spain so it may be that is the Euro p/n.

    Revised
    USDM/AUD/CAN 3SGELC (both egr and 02 systems)
    -86'-20160 (8/85-7/86)
    -87'-20110 (8/86-7/87)
    -88'-20110
    -89'-20320

    JDM 3SGELU (no egr but has 02 system)
    -86'-20150
    -87'-20150
    -88'-20310
    -89'-20310 (8/87-12/88)
    -20311 (1/89-7/89)

    EURO 3SGEL (no egr no 02 systems)
    -86'-20180
    -87'-20180
    -88'-20180
    -89'-20180

    ST165
    - JDM - 28280
    - USDM - 20360
    - EURO - 20370

    ST185 also uses T-VIS, here are the ECU's
    93
    JDM
    RC 89661-2B310
    GT-4 89661-2B2820

    Euro
    Grp A 89661-2B320
    GT-4 89661-20770 or 89661-2B300

    US/Can
    Alltrac 89661-20760 or 89661-20761 or 89661-2B290

    Other
    Grp A 89661-2B320
    GT-4 89661-20770 or 89661-2B300

    92
    JDM
    RC 89661-2B310
    Grp A 89661-20751
    Wide-4 89661-2B280
    Narrow-4 89661-20750 or 89661-20751

    Euro
    Grp A 89661-2B320
    GT-4 89661-20770 or 89661-2B300

    US/Can
    Alltrac 89661-20760 or 89661-20761 or 89661-2B290

    Other
    Grp A 89661-2B320
    GT-4 89661-20770 or 89661-2B300

    91
    JDM
    RC 89661-2B310
    Grp A 89661-20751
    Wide-4 89661-2B280
    Narrow-4 89661-20750 or 89661-20751

    Euro
    Grp A 89661-2B320
    GT-4 89661-20770 or 89661-2B300

    US/Can
    Alltrac 89661-20760 or 89661-20761 or 89661-2B290

    Other
    Grp A 89661-2B320
    GT-4 89661-20770 or 89661-2B300

    90
    JDM
    Grp A 89661-20751
    Narrow-4 89661-20750 or 89661-20751

    Euro
    GT-4 89661-20770 or 89661-2B300

    US/Can
    Alltrac 89661-20760 or 89661-20761 or 89661-2B290

    Other
    GT-4 89661-20770 or 89661-2B300

    On the same note, the 4A-GE also uses T-VIS and has a higher rev limit etc
    Has anyone tried using one on a 3S-GE?
     
    Last edited: Feb 7, 2013
  5. eNtraxGT88

    eNtraxGT88 Well-Known Member Donated!

    so to answer OP, don't buy that ecu, it's for a 3S-FE.

    we should build up that too

    so far i have 20280 for prefacelift, 20440 for facelift for 3S-FE
     

Share This Page